Blauberg VENTO A50 Pro

Print version

Heat recovery single-room units. Maximum air capacity up to 53 m³/h.

EAN4058448022746

Add to project

To comparison

Description
Characteristics
Downloads
DIMENSIONS
Accessories

Description

USE
Arrangement of efficient energy-saving supply and exhaust single-room ventilation in flats, houses, cottages, social and commercial premises.Heat recovery minimises ventilation heat losses.	Humidity balance and controllable air exchange create individually set microclimate.Coordinated network based on several integrated single-room ventilation units with central control.
DESIGN

HEAT AND MOISTURE REGENERATION
High-tech ceramic energy accumulator with heat recovery up to 90 %.	Due to its cellular structure it has a larger contact area surface and high efficiency. The energy accumulator is featured with excellent heatconducting properties and thermal energy storage capacity.
Unit operating logic in winter period

Warm stale air is extracted from the premise, flows through the ceramic regenerator and transfers a part of the accumulated heat and moisture to it.As the ceramic regenerator gets warmed up, the unit switches to the supply mode.	Clean cold intake air flows through the regenerator and absorbs accumulated heat and humidity.When the ceramic regenerator is cooled down, the unit is switched to the extract air mode.
CONTROL
The integrated automation system enables operation of the unit at the first low speed or the second high speed: ventilation mode (air supply or air extract); reversible heat regeneration mode. The unit operation mode control is performed by means of an external control block with a power transformer: in VENTO A50 Pro / A50-1 Pro / A50 S Pro / A50-1 S Pro delivery set included (model SEA-T12); available upon separate order for VENTO A50 / A50-1/ A50 S / A50-1 S (model SEA-T12 or SEA).
To arrange a central controlled ventilation system based on 4 units connect three VENTO A50 / A50-1/ A50 S / A50-1 S units to one VENTO A50 Pro / A50-1 Pro / A50 S Pro / A50-1 S Pro unit with SEA-T12 control and power unit. No extra accessories are required.

To arrange a central controlled ventilation system based on more than 4 units connect a required number of the units, one SEA three-position switch and several 12 W AT-12 transformers or 40 W AT-40 transformers, depending on the total unit power consumption to one VENTO A50 / A50-1/ A50 S / A50-1 S unit.

MOUNTING
The unit is designed for external through-the-wall installation inside a prepared round hole in the outer wall of the building.The best ventilation solution is pairwise installation of reverse phase connected units. Some units supply fresh air to the room and the other units extract stale air from the room. This allows to arrange the most efficient balanced ventilation.	In case of brand new construction the units are mounted in two stages: pre-installation at the stage of the indoor finishing and outer decorative wall finishing. It includes installation of the telescopic air ducts, outer ventilation hood and laying out of electric cables. final mounting before commissioning of a house. It includes installation of the regenerator, the filter, connection of the ventilation unit and automation. If mounting of the ventilation hood on the outer wall is undesirable it may be flush mounted and the external grille may be inserted into the outer window jamb using the KIT BlauPlast 204x60-1 pre-installation kit. Available upon separate order.

Angular mounting into a wall with standard thickness using KIT BlauPlast 204x60-1

Characteristics

Parameter	VENTO A50 Pro (1 speed)	VENTO A50 Pro (2 speed)	Measurement unit
Voltage	220-240	220-240	V
Frequency	50	50	Hz
Voltage	220-240	220-240	V
Power	3.68	4.83	W
Current	0.021	0.026	A
RPM	599	1155	min^-1
Maximum air flow	26	53	m³/h
Sound pressure level at 1 m	24	34	dBА
Sound pressure level at 3 m	14	24	dBА
Outdoor sound pressure attenuation	18	18	dBА
Regeneration efficiency	≤ 90	≤ 90	%
Ingress protection rating	IP24	IP24	-
Remote control panel	Mechanical	Mechanical	-
Air duct	150	150	-
SEC class	A	A	-
Mounting	wall mounting	wall mounting	-

Documents archieve

DIMENSIONS

Accessories

ACCESSORY NAME	DESCRIPTION
SEA-T12 (230/12) control and power unit	SEA-T12 is an external control unit with a 12 W power transformer. It is included into VENTO A50 / A50-1 Pro and VENTO A50 / A50-1 S Pro units standard delivery set.
SEA control unit	SEA is an external control unit for the unit operation mode control.
AT-12 (230/12) power transformer	AT-12 is a 12 W power transformer for synchronous connection of 4 units. Used jointly with SEA control unit it ensures a central controllable ventilation system.
AT-40 (230/12) power transformer	AT-40 is a 40 W power transformer for synchronous connection of 12 units. Used jointly with SEA control unit it ensures a central controllable ventilation system.
Pre-installation kit for mounting into a wall with standard thickness Pre-installation Kit VENTO A50	Includes: Round Ø150 mm air duct, 240 up to 460 mm long. AH 150 outer ventilation hood. Plastic foam plug.
Pre-installation kit for mounting into a thin wall Pre-installation Kit VENTO A50 S	Includes: Round Ø150 mm air duct, 120 up to 420 mm long. AH-S 150 outer ventilation hood. Plastic foam plug.
Final mounting kit Completion Kit VENTO A50	Includes: Ceramic regenerator Ø150 mm. VENTO A50 ventilation unit. G3 filters.
Final mounting kit Completion Kit VENTO A50-1	Includes: Ceramic regenerator Ø150 mm. VENTO A50-1 ventilation unit. G3 filters.
Mounting kit for angular installation in walls with standard thickness KIT BlauPlast 204x60-1	Includes: Plastic ventilation grille 230x86 mm. Plastic air duct 204x60 mm. Plastic connecting bend from Ø150 to 204x60 mm.